Chat with Us
Back to Product Guides

Dr. Dabber Switch User Guide — Desktop Induction E-Rig

2Last updated:

Complete guide to the Dr. Dabber Switch desktop E-Rig with induction heating, 25 heat settings (300-800°F), dual-use for concentrate and dry herb, and Advanced/Crystal modes.

Complete Dr. Dabber Switch User Guide

The Dr. Dabber Switch is a desktop E-Rig that uses Induction Heating instead of traditional coils, delivering faster and more even heating. It features 25 heat settings (300-800°F) and supports both concentrates and dry herb in a single device.

---

Unboxing — What Is in the Box

  • Dr. Dabber Switch base unit (built-in battery)
  • Glass Attachment
  • Quartz Induction Cup (for concentrates)
  • Ceramic Induction Cup (for dry herb)
  • Carb Cap
  • Dabber Tool
  • USB-C charging cable
  • Device stand

Note: Fully charge the device before first use.

---

Initial Setup

Step 1 — Select Your Induction Cup

  • Use the Quartz Cup for concentrates.
  • Use the Ceramic Cup for dry herb.

Place the selected Cup into the Induction well on top of the device.

Step 2 — Attach the Glass

Place the Glass Attachment onto the base and fill with clean water through the mouthpiece. Water level should be just above the percolator.

Step 3 — Power On

Press the Power button 5 times. The OLED display will show the current heat level and mode.

---

25 Heat Settings (300-800°F)

The Switch offers 25 precise heat levels. Use the Up/Down buttons to navigate between them.

RangeTemperatureCharacteristics
1-8300-450°FLow Temp — Flavor-focused, light vapor
9-16450-600°FMedium — Balanced flavor and vapor
17-25600-800°FHigh Temp — Dense vapor, max extraction
RangeTemperatureCharacteristics
1-6300-380°FExcellent flavor, light vapor
7-14380-420°FBalanced, moderate vapor
15-25420-800°FMaximum extraction, thick vapor
---

Operating Modes

Standard Mode

Default mode. Heats to the selected level and holds temperature. Suitable for most users.

Advanced Mode

Hold the button for 3 seconds to enter Advanced Mode. This allows real-time temperature adjustment during an active session — ideal for users who want fine-grained control.

Crystal Mode

A specialty mode for concentrates that prioritizes pure flavor. It operates at lower temperatures and pairs with the Crystal Quartz Cup for premium taste.

---

How to Use with Concentrates

1. Insert the Quartz Induction Cup.

2. Set your heat level (recommended: start at level 9-12).

3. Press the heat button — wait for Induction heating (approximately 4-5 seconds).

4. Use the Dabber to load concentrate into the Cup.

5. Place the Carb Cap and inhale slowly.

How to Use with Dry Herb

1. Insert the Ceramic Induction Cup.

2. Grind herb to a medium consistency and load into the Cup. Do not pack tightly.

3. Set your heat level (recommended: start at level 5-8).

4. Press the heat button and wait until ready.

5. Inhale slowly through the mouthpiece.

---

Maintenance and Cleaning

After Concentrate Sessions

  • Swab the inside of the Quartz Cup with a Cotton Swab dipped in Isopropyl Alcohol while still warm.
  • Replace the water in the glass after each use.

After Dry Herb Sessions

  • Tap spent herb material out of the Ceramic Cup.
  • Use a brush to clean any remaining residue.
  • Wipe with Alcohol regularly.

Deep Clean

  • Soak the Induction Cup in Alcohol for 30 minutes. Rinse with clean water and air dry.
  • Clean the glass with Alcohol.

---

Pro Tips

  • Induction means no coil: No coil burnout risk since there is no heating coil to degrade.
  • Dual-use flexibility: Swap Cups easily to switch between concentrate and dry herb sessions.
  • Desktop with a battery: The Switch is portable despite its desktop form factor.
  • Start low and go up: Begin at a mid-range level and increase gradually for the best flavor.

Share Article

Was this article helpful?