DynaVap M7 / M7 XL Complete User Guide

DynaVap The M7 / M7 XL - Complete User Guide

The DynaVap M7 is the flagship model in the DynaVap lineup. Built entirely from stainless steel, it is durable, lightweight, and designed for reliable performance. The M7 XL is the extended version for those who prefer a longer device for easier handling. Both are designed and manufactured in the USA.

---

Unboxing - What's in the Box

When you open your DynaVap M7, you will find:

• DynaVap M7 device (fully assembled and ready to use)
• Captive Cap (stays attached to the Tip so it never gets lost)
• Storage Tube (protective case for carrying on the go)
• Quick start card

Device components: Cap (heat indicator), Tip (chamber/bowl), Body (with Airport groove), Condenser (internal cooling tube), Mouthpiece (draw end)

---

First-Time Setup (Burn-off)

Before your first session, perform a burn-off to remove any manufacturing residue:

1. Leave the chamber empty - do not pack any material

2. Heat the Cap with a Torch until you hear the click

3. Wait for the cool-down click

4. Repeat 2-3 times

5. Your device is now ready for use

---

How to Pack the Chamber

1. Grind your herb to a medium consistency. Not too fine, not too coarse.

2. Lift the Captive Cap up from the Tip

3. Dip the Tip into your ground herb, or pinch a small amount and drop it in

4. Fill to about 70-80% of the chamber. Do not tamp or press down.

5. Close the Cap back over the Tip

---

Torch Heating Technique - Step by Step

This is the most important part of using your DynaVap:

1. Hold the device at a 45-degree angle, gripping from the mouthpiece end

2. Light your torch - a single-flame torch is recommended for precision

3. Aim the flame about 2-3 cm from the Cap, letting the tip of the flame lightly touch the Cap

4. Rotate the device continuously by rolling it between your fingers

5. Listen for the CLICK - this takes roughly 5-10 seconds

6. Stop heating immediately once you hear the click

7. Draw slowly and steadily for about 10-20 seconds

8. Wait for the cool-down click before heating again

---

Temperature Control Guide

Heat Near the Tip of the Cap (Low Temp)

• Temperature around 150-170°C / 300-340°F
• Produces rich, flavorful vapor with full terpene expression
• Wispy, light vapor - ideal for flavor chasers

Heat the Middle of the Cap (Medium Temp)

• Temperature around 180-195°C / 356-383°F
• Best balance of flavor and vapor production
• Recommended starting point for beginners

Heat Near the Base of the Cap (High Temp)

• Temperature around 200-220°C / 392-428°F
• Produces thick, dense clouds with maximum extraction
• Less flavor but stronger effects

---

Airport - Airflow Control

The M7 has an Airport (small hole on the Body) for controlling draw resistance:

• Cover the Airport (finger over the hole) = tight draw, concentrated vapor
• Leave the Airport open = airy draw, cooler vapor, less dense
• Half-cover = balanced draw, recommended for beginners

---

Cleaning & Maintenance

Clean your M7 every 3-5 sessions for optimal performance:

1. Disassemble all components (Cap, Tip, Body, Condenser, O-rings)

2. Remove O-rings first - do NOT soak O-rings in Isopropyl Alcohol (ISO)

3. Soak metal parts in 90%+ ISO for 10-15 minutes

4. Use a pipe cleaner or cotton swab to scrub inside the Condenser and Tip

5. Rinse with hot water and dry thoroughly

6. Apply a thin layer of Dynawax or food-grade wax to the O-rings before reassembling

---

Troubleshooting