DynaVap UniDyn (Ball Vape) Guide - Heat Soak Technique & Induction Heater

DynaVap UniDyn Guide - Ball Vape Attachment

The DynaVap UniDyn is a Ball Vape Attachment that fundamentally changes how you use a DynaVap. Instead of heating a Cap in the traditional way, the UniDyn uses small metal balls as a thermal mass to store and transfer heat. This delivers more even, consistent, and efficient extraction than the standard cap-and-tip method.

---

Unboxing - What's in the Box

• UniDyn Ball Vape Attachment (the main attachment)
• Metal Balls (thermal mass beads - pre-loaded inside)
• Screen / Filter for filtration
• Quick start guide

---

How It Works - Different from Standard DynaVap

Standard DynaVap (Cap + Tip)

• Heat the Cap directly, heat transfers through Cap to Tip, extracts material
• Requires continuous rotation
• Click indicates temperature

UniDyn (Ball Vape)

• Heat the metal balls until they store significant thermal energy
• When you draw air through, hot air passes through the balls then over the herb
• Much more even heat distribution
• No click indicator - relies on the Heat Soak technique

---

How to Assemble the UniDyn

1. Remove the Cap and Tip from your existing DynaVap Body

2. Verify the metal balls are present inside the UniDyn

3. Place the Screen at the bottom for filtration

4. Attach the UniDyn to your Body in place of the original Tip + Cap

5. Ensure everything is securely assembled

---

Heat Soak Technique - The Heart of the UniDyn

Since the UniDyn has no click like a standard DynaVap, you use the Heat Soak technique:

Basic Heat Soak Method

1. Light your torch (single or double flame recommended)

2. Aim the flame at the top section of the UniDyn (where the balls are)

3. Heat for approximately 20-30 seconds while slowly rotating

4. Stop heating and wait 5-10 seconds to let heat penetrate the balls (the Soak)

5. Draw slowly and steadily - hot air passes through the balls to extract vapor

6. You can take multiple draws from a single heat cycle

Advanced Heat Soak

• Longer heating (30-40 seconds) for denser, thicker vapor
• Longer soak time (10-15 seconds) for the most even heat distribution
• Draw while gently heating for extended, longer sessions

---

Pairing with an Induction Heater

The UniDyn pairs exceptionally well with an Induction Heater (IH):

Benefits of IH with UniDyn

• Consistent results every time - no guesswork on timing
• More convenient than using a torch
• The balls receive heat from the IH more evenly
• Safer for indoor use - no open flame

How to Use with an Induction Heater

1. Insert the UniDyn into the Induction Heater

2. Press and hold the heat button for about 15-25 seconds (varies by IH model)

3. Remove and allow a 5-second heat soak

4. Draw slowly and enjoy

---

Packing the Chamber for UniDyn

• Grind your herb to a medium to coarse consistency
• Pack loosely in the chamber below the balls
• Do not tamp down - air must flow through the balls and into the material
• Use less material than standard DynaVap since extraction is more efficient

---

Cleaning & Maintenance

1. Detach the UniDyn from the Body

2. Carefully pour out the metal balls (do not lose them!)

3. Soak balls and metal components in 90%+ ISO for 15 minutes

4. Clean or replace the Screen if it is clogged

5. Rinse with hot water and dry thoroughly

6. Reassemble carefully

---

Troubleshooting

Tips for Best Results

1. Patience with Heat Soak - let the heat fully distribute before drawing

2. Slow draws work better than fast pulls with ball vapes

3. Stir the chamber between heat cycles for more even extraction

4. Clean regularly - ball vapes accumulate residue faster due to high efficiency

5. The UniDyn improves with practice - your technique will get better over time